Beisler 58 Instructions d'exploitation télécharger pdf (Page 30)

2-10

7 Distance of seam end revs [5 mm] (0 - 99 mm)

distance with the revs of parameter 5

8 Stitch length seam start [1,5 mm] (0,5 - 3 mm)

stitch length at seam start for tack or stitch condensation

9 Stitch length in the seam [2,4 mm] (0,5 - 3,5 mm)

10 Stitch length seam end [1,5 mm] (0,5 - 3,0 mm)

freely selectable, effects on tack and stitch condensation at seam end

11 Distance stitch length seam start [10 mm] (0,5 - 99 mm)

distance with stitch length of parameter 8

12 Distance stitch length seam end [10 mm] (0,5 - 99 mm)

distance with stitch length of parameter 10

13 Tack length seam start [10 mm] (0 - 20 mm)

if this value is set to 0, stitch condensation will be sewed automatically

14 Tack length seam end [10 mm] (0 - 20 mm)

if this value is set to 0, stitch condensation will be sewed automatically

15 Slope at seam start [3 mm] ( 0 - 10 mm)

seam offset (difference left/right needle) at seam start

16 Slope at seam end [3 mm] (0 - 10 mm)

seam offset at seam end

17 Enable center knife [17 mm] (0 - 30 mm)

depending on seam and knife width, the center knife should cut est. 1

mm further than the mitre knife

18 Disable center knife [0 mm] (0 - 30 mm)

depending on seam and knife width, the center knife should cut est. 1

mm further than the mitre knife

19 Thread monitor on after [30 mm] (0 - 99 mm)

distance after which the thread monitor will be enabled; change this

parameter if seam length < 30 mm

20 Thread monitor filter [07] (00 - 99)

the smaller the digit, the more sensitive the upper thread monitor

reacts; 99: thread monitor disabled

21 Length vylene seam start [60 mm] (0 - 99 mm)

vylene overlay at seam start

22 Length vylene seam end [80 mm] (0 - 99 mm)

vylene overlay at seam end

23 Duration final roller [0,5 Sek.] (0 - 99 Sek.)

exact positioning of the work piece to be stacked

24 Intermediate stop selection + pos. [0 cm] (0 - 48 cm]

enter a position, where the main clamp shall be driven to after

stacking; 01 cm = main clamp is driven to the insertion station

25 Pick up part selection + pos. [0 cm] (0 - 48 mm)

if a value is defined, the main clamp pressure is released after mitre

cutting automatically and the work piece will be driven to the set

position; 01 cm = work piece is driven to the insertion station

26 Revs center knife [40%] (10 - 99%)

definition of the cutting speed

27 Revs final roller [99%] (10 - 99%)

a reduction achieves an optimized positioning for the stacking

30 Flap clamp mode >> see further below

31 Folding slide mode

00: left + right fold slider enabled

01: left fold slider enabled

02: right fold slider enabled

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 77 78

Commentaires sur ces manuels

Pas de commentaire

Beisler 58 Instructions d'exploitation Page 30

Commentaires sur ces manuels

Produits connexes et manuels pour Machines à coudre Beisler 58